Speco Technologies Security Camera CVC 614C User Manual

®
Instruction Manual  
CVC-614C High Resolution Color Camera  
and  
CVC-865DN/24 High Resolution Color  
Camera With Mechanical IR Cut Filter  
200 New Highway  
Amityville . NY . 11701  
1-800-645-5516  
Fax: 631.957.9142 or 631.957.3880  
Speco Technologies CVC-614C : CVC-865DN/24  
Instruction Manual  
1
 
Introduction  
FCC Information  
This equipment has been tested and found to comply with the limits of a class A digital device, pursuant to  
part 15 of the FCC rules and also guaranteed with CE approval. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This equipment generates,  
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the  
user will be required to correct the interference at his or her own expense.  
The user's manual or instruction manual for an intentional or unintentional radiator shall caution the user that  
changes or modifications not expressly approved by the party responsible for compliance could void the  
users' authority to operate the equipment.  
Warning  
To prevent fire or shock hazard, do not expose the unit to rain or moisture.  
This symbol alerts the user to the presence of non-insulated dangerous voltage within the  
product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.  
This symbol alerts the user to the presence of important operating and maintenance  
(servicing) instructions in the literature accompanying the product.  
Handle the camera with care.  
Be careful while handling or installing the camera. Do not drop it or subject it to strong shock or vibration to  
prevent any damages to it. Do not disassemble it or place it on an unstable base.  
Never face the camera toward the sun.  
The camera's picture may be influenced when working in unusual brightness environment. Sun light may do  
influence on the picture quality or camera itself. Never aim the camera at the sun or other extremely bright  
objects whether it is in use or not.  
Cleaning.  
Do not touch the surface of CCD sensor by hand directly. Using lens tissue or a cotton tipped applicator and  
ethanol to clean the CCD sensor and camera lens. When the camera is not in use, always put the cover cap on  
the lens mount.  
Operation temperature.  
This camera is designed for use in general purpose indoor CCTV application. Only operate your camera  
between the temperature of -10to +60(14to 140)  
Speco Technologies CVC-614C : CVC-865DN/24  
Instruction Manual  
3
 
About this Manual  
This user manual covers the following models listed below. Before installing and using the camera,  
please read this manual carefully. Be sure to keep it handy for later use.  
Dimensions  
(Unit: mm):  
Features  
Accepts C or CS mount lens.  
Low light, high sensitivity.  
DC/Video Drive  
Back Focus  
Available in Selected Models  
AGC (Automatic Gain Control)  
Back light compensation.  
External Sync.(Line Lock)  
Day & Night (Removable)  
Under different light conditions, it will automatically changeover the color to B/W and  
vice versa. *Perfectly for clear viewing  
High Resolution 580 TV Lines (HQ1)  
Min. illumination of 0.5Lux, F1.4 (HQ1)  
Accessories  
The packaging contains:  
z
z
z
z
z
Camera x 1  
Instruction Manual x 1  
C/CS Mount adjusting ring x 1  
Connector of Auto Iris Lens x 1  
Adjustment Tools x 1  
If any parts are missing or damaged, contact the dealer you purchased the camera from.  
Speco Technologies CVC-614C : CVC-865DN/24  
Instruction Manual  
4
 
Camera Functions  
Parts Descriptions  
1. C mount lens ring adapter.  
If you are using a CS mount lens, remove the C mount lens ring adapter.  
2. Flange back adjusting ring  
If back focus adjustment is required, loosen the flange back locking screw,  
and adjust back focus by rotating the ring.  
3. Mounting bracket screw hole (1/4" -20 UNC)(top)  
4. Auto iris lens connector (mini jack)  
5. Video output terminal (BNC)  
6. Power supply indicator  
7. Power input terminal  
8. Video / DC drive auto iris lens selector  
9. ALC level adjuster - for DC-DRIVE lens  
10. Function control DIP switch  
*10-1: Function control DIP switch (WB mode)  
*11. Color & B/W Level switch  
*12.Phase adjustor ( button)  
*Selected models.  
Speco Technologies CVC-614C : CVC-865DN/24  
Instruction Manual  
5
 
Camera Functions  
Function Description  
1.  
Auto Electronics Shutter (AES)  
When using a DC Drive or Video Drive Auto Iris Lens, turn off the AES. When a Fixed Iris or Manual  
Iris Lens is used, turn the AES on to adjust the shutter speed automatically.  
2. Automatic Gain Control (AGC)  
AGC can automatically amplify the digital signal to adjust are for the difference of light level.  
3. Auto Tracking White Balance (ATW) / Auto White Balance (AWB)  
When the color difference is too obvious, turn the AWB on to have better balanced color, Set the  
switches to ATW to have a normal color picture.  
4. Aperture Gain (APG)  
APG cam make the picture becomes sharper, switch to OFF for normal mode.  
5. Back Light Compensation (BLC)  
When BLC is ON, the AGC, AES and IRIS operating point is determined by averaging over the  
center area instead of entire field-of-view, so that a dimly-lit foreground object at center area can be  
clearly distinguished from brightly-lit backgrounds. When operating the camera outdoor, turn the  
BLC on to get clear picture of object on screen. For indoor using or when operating the camera in  
low light environment turn, the BLC ON as well.  
6. DAY & NIGHT (ICR removable)  
The camera provides automatic mode changeover from color to B/W or B/W to color by sensing  
different light conditions. It remains at true color mode in the day condition for optimal color and  
switched to B/W mode in night condition for clear viewing by removing the Infrared Cut Filter.  
7. Flickerless (FLC)  
This switch captures the wide and intense range of color of some light sources and adjust the color,  
gain, electronic shutter control and tracking balance to produce a good quality color picture.  
8. Internal Line Lock (INT / LL)  
The Line Lock is designed to stabilize the image. Always switch it on. Line Lock sync is interchange  
and only available when with an AC Power source. It's unavailable with 12V DC power.  
Speco Technologies CVC-614C : CVC-865DN/24  
Instruction Manual  
6
 
DIP Switch Control  
Function  
Format  
LL  
Description  
For stabilizing the image  
Use the (  
) button to adjust.  
LL - IN  
IN  
OFF  
Initial setting is IN.  
Normal:1/60 (1/50)  
NTSC:1/60~1/100000  
PAL:1/50~1/100000  
ON  
OFF-AES  
BLC-OFF  
AES mode  
BLC  
OFF  
OFF  
BLC OFF.  
AGC OFF.  
OFF-AGC  
Turn it on in the dark environment to get  
clear image.  
AGC  
Use to change shutter speed under  
flicker state.  
NTSC:1/120  
PAL:1/100  
FLC  
FLC-OFF  
Note: Can only be used when AES is  
on.  
OFF  
H
L
H
L
FLC OFF  
When the color temperature of the  
environment dramatically changes, you  
can adjust WB mode/switches to have  
better color image.  
WB1  
WB2  
WB3  
H
L
*Please see the “White balance mode”.  
White Balance Mode  
WB1  
WB2  
WB3  
MODE  
Remark  
ATW  
Natural: Outdoor and environments  
under daylight.  
L
L
L
(Auto White balance)  
MWB  
L
L
L
H
L
Use the (  
) button to adjust.  
(Manual White balance)  
H
Push  
Hold  
Similar with ATW.  
(White balance mode-manual)  
When you use this function, pointing the  
camera to a specific area, ex: white  
paper, you can then apply the color to  
elsewhere.  
L
H
H
H
H
L
L
L
fixed value (4700°K)  
fixed value (3200°K)  
For your reference, please check on  
Color Temperature chart.  
H
H
H
H
H
L
fixed value (4200°K)  
fixed value (6300°K)  
K= Kelvin color Temperature  
H
Speco Technologies CVC-614C : CVC-865DN/24  
Instruction Manual  
7
 
Camera Functions  
Color Temperature Chart (White Balance)  
Light Sources  
Summer Skylight  
Daylight Shade  
Degrees (°k)  
12000 – 25000°k  
10000°k  
Skylight  
Overcast  
Studio Electronic Flash  
Daylight/ Auto Flashlight  
Fluorescent bulbs  
8000~10000°k  
6500~7500°k  
6500°k  
5500°k  
4200~5000°k  
4500°k  
Cool white- fluorescent bulbs  
Warm white- fluorescent bulbs  
Studio Lights  
3500°k  
3400°k  
Professional Tungsten photo lamp  
Household bulb  
3200°k  
2700~3200°k  
2000~3000°k  
1900°k  
SunriseSunset  
Candle  
note: Please note that the values are approximations because many factors affect  
color temperature.  
Speco Technologies CVC-614C : CVC-865DN/24  
Instruction Manual  
8
 
Installation Guide  
Installing the lens  
1. Remove the lens cap from the front of the camera.  
2. If you are using a C mount lens, screw the lens directly into the camera.  
3. If you are using a CS mount lens, remove the C mount lens ring adapter.  
4. When using a fixed iris lens, switch the shutter control to AES ON.  
5. When using a manual adjustable iris lens, switch the shutter control to AES OFF.  
6. When using a Video servo auto iris lens or DC servo auto iris lens, switch the shutter control  
to AES OFF.  
Auto iris lens connection  
1. When using auto iris lens (with EE amp)  
Set the lens selector to the "Video" position.  
PIN  
DEFINITION  
LENS CABLE LEAD  
1
2
3
4
DC +12 V  
Video iris  
NC  
Red  
White  
-
Ground  
Black  
2. DC servo auto iris lens (without EE amp)  
Set the lens selector to the "DC" position.  
PIN  
DEFINITION  
Damping -  
Damping +  
1
2
3
4
Driving+  
Driving-  
To ensure correct lead connection, please refer to the instructions on the lens.  
Speco Technologies CVC-614C : CVC-865DN/24  
Instruction Manual  
9
 
Installation Guide  
Connections  
1. Keep the cameras' power OFF during the installation.  
2. Ensure that the input voltage is correct for the plug pack; both the camera and the plug pack may be  
damaged if the voltage is incorrect.  
3. Terminate the camera output to 75 ohms.  
Use 75-ohm coaxial cable (RG-59/U, RG-6/U, RG-11/U).  
Always set the last monitor termination switches to 75 ohms, and set the termination switches of  
intermediate monitors to HIGH (HI-Z)  
4. The table below shows the Maximum recommended cable length.  
RG-59 / U  
(3C-2V)  
RG-6 / U  
(5C-2V)  
RG-11 / U  
(7C-2V)  
Type of Coaxial Cable  
Recommended  
Maximum Cable Length  
30 ft.  
100m  
660 ft.  
200m  
825 ft.  
250m  
Auto Iris Lens Adjustments  
Once the lens is screwed in completely to its mechanical stop position, you will then be  
able to rotate lens chassis back to suit the set-up position of the camera.  
The back focus adjustment is accessible at the front end of the camera. It allows you to  
adjust the back focal length or picture focus.  
*Note: it does not apply to all types of lens, please contact with your dealer you  
purchased your lens from.  
Troubleshooting  
Problem  
What to Check  
Is the system power on?  
Is the cable connected properly?  
Has the lens cap been removed?  
Is the illumination proper?  
- No picture appears on the monitor  
Is the monitor properly adjusted?  
Is the lens mount ring proper?  
Is the lens clear?  
Is the lens properly focused?  
Is the monitor terminated properly?  
- The picture is not clear  
Note: If dust adheres to the lens, the picture quality will suffer.  
To clean the lens, wipe lightly with a soft cloth or commercially available lens cleaning paper.  
Speco Technologies CVC-614C : CVC-865DN/24  
Instruction Manual  
10  
 
Specifications  
Color HQ-1 Camera  
Item  
CVC-614C  
CVC-865DN/24  
Description  
1/3" Color HQ1 Camera  
1/3" Color HQ1 Camera with ICR  
(Mechanical IR Cut Filter)  
DSP  
Sony HQ1  
Pick up Element  
Sony Super-HAD CCD Image Sensor  
Number of Pixels  
Auto Electronics Shutter  
AGC  
<NTSC> 768 (H) × 494 (V)  
ON-OFF  
ON-OFF  
ALC  
WB  
Low-High  
ATW/ MWB (PUSH-HOLD) 3200°k/ 4200°k/ 4700°k/ 6200°k  
Back Light Compensation  
ON-OFF  
ON-OFF  
IN-LL  
FLC  
Line Lock*  
Sync. Mode  
Internal Sync.  
Scanning System  
Resolution  
2:1 Interlace  
580 TV Lines  
More than 48dB  
S/N Ratio  
Gamma  
0.45  
Minimum illumination  
0.5 Lux, F1.4  
Horizontal Sync. Frequency  
<NTSC>15.734 KHz  
Video Output  
1.0 Vp-p, 75 ohm  
Power Source  
AC/DC(12~24)V, AC 99V~240V  
(AC/DC)3W  
Power Consumption  
Operating Temperature  
-10to +60℃  
Lens Mount  
Shutter Control  
Dimensions  
Net Weight  
C/CS mount  
<NTSC>1/60-1/100,000 sec.  
123(L) x 57(W) x 52(H) mm  
<AC/DC type>0.44kg  
* Specifications are subject to change without prior notice.  
* Line Lock is available when AC Voltage is used.  
Speco Technologies CVC-614C : CVC-865DN/24  
Instruction Manual  
11  
 
®
Speco Technologies  
200 New Highway  
Amityville . NY . 11701  
1-800-645-5516 Fax: 631.957.9142 or 631.957.3880  
CR300000209  
Speco Technologies CVC-614C : CVC-865DN/24  
Instruction Manual  
12  
 

Sharp Digital Camera QSINUFO User Manual
Shibaura Lawn Mower SR525 User Manual
Sonic Blue Speaker System XJR User Manual
Sony Portable Speaker SS CR190 User Manual
Sony Projector VPL CX86 VLPCX76 User Manual
Sony Stereo Amplifier XM GTR2202 User Manual
Spectra Headphones TW4080 User Manual
Symbol Technologies Telephone PDT 7500 Serie User Manual
Tannoy Portable Speaker DC8i User Manual
Targus Laptop NOTEBOOK DOCKING station with video User Manual