Speco Technologies Security Camera VLB11SCSFF User Manual

VLB11SCSFF  
550 Line Color Bullet Camera  
Focus Free  
Wall & Ceiling Mountable  
Please read this manual thoroughly before operation and keep  
it handy for further reference.  
 
WARNING & CAUTION  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
CAUTION  
:
TO REDUCE THE RISK OF ELECTRIC SHOCK  
D O N O T R E M O V E C O V E R ( O R B A C K ) .  
NO USER SER VICEABLE PART S INSIDE  
R E F E R S E R V I C I N G T O Q U A L I F I E D  
S E R V I CE PER SONNEL._______________  
The lighting flash with an arrowhead symbol, within an equilateral triangle is  
Intended to alert the user to the presence of un-insulated “dangerous voltage”  
within the product’s enclosure that may be of sufficient magnitude to constitute  
a risk of electric shock to persons____________________________________  
The exclamation point within an equilateral triangle is intended to alert the user  
to the presence of important operating and maintenance (serving) instructions  
in the literature accompanying the appliance__________________  
INFORMATION -This equipment has been tested and found to company with  
l i m i t s f o r  
These limits are designed to provide reasonable protection against harmful  
I nterference W hen the equipments operated in commercial environment.  
a
c l a s s  
a
d i gi t a l device Pursuant to part 15 of the FCC rules.  
a
This equipment generates, uses, and Can Radiate radio frequency energy and  
if not installed and used in accordance with the instruction manual, may Cause  
Harmful interference to radio communications. Operation of this equipment in  
a
r e s i d e n t i a l a r e a i s l i k e l y t o c a u s e h a r m f u l i n t e r f e r e n c e i n w h i c h  
Case the user will be required to correct the interference at his own expense.  
WARNING – Change or modification not expressly approved by the manufacturer could void  
the user’s authority to operate the equipment__________________________________  
CAUTION : To prevent electric shock and risk of fire hazards.  
DO NOT use power sources other than that specified.______  
DO NOT expose this appliance to rain or moisture.000  
This installation should be made by a qualified service person and should conform to all local codes.  
2
 
PACKAGE CONTENTS  
Please make sure that the following items are included  
in the package:  
1 VLB11SCSFF Camera  
3 Mounting Screws  
1 Video test Connector  
1 Wrench  
Please leave this manual with the end-user for future  
reference.  
4
 
PRECAUTIONS  
THIS CAMERA SHOULD BE ONLY INSTALLED BY QUALIFIED  
PERSONNEL  
TO PREVENT A FIRE OR ELECTRICAL HAZARD PLEASE USE  
PROPER POWER CABLE  
DO NOT CLEAN THE COVER WITH AN ABRAISIVE CLEANING  
MATERIAL - PLEASE USE A SOFT CLOTH OR TISSUE TO  
CLEAN THE COVER  
THERE ARE NO USER-SERVICEABLE PARTS INSIDE.  
PLEASE DO NOT DISASSEMBLE THIS CAMERA OTHER THAN  
TO MAKE INITIAL ADJUSTMENTS  
PLEASE USE A UL APPROVED REGULATED 12 VOLT DC  
POWER SUPPLY  
PLEASE USE APPROPRIATE LOW VOLTAGE POWER CABLE  
TO PREVENT FIRE OR ELECTRICAL SHOCK  
PLEASE INSURE THAT YOUR INSTALLATION AREA CAN  
SUPPORT THE WEIGHT OF THE CAMERA  
PLEASE HANDLE THIS CAMERA CAREFULLY:  
- DON’T USE A STRONG OR ABRASIVE DETERGENT WHEN  
CLEANING THE CAMERA.  
- DON’T EXPOSE THE CAMERA TO DIRECT SUN  
5
 
CAMERA INSTALLATION  
CONNECT POWER CABLE  
1. WHEN USING 12 VOLTS DC (constant voltage 500 mA)  
Power Input :RED  
Center : (+)  
DC 12V Power Supply  
2. CONNECT VIDEO CABLE  
-CONNECT BNC CABLE TO THE BNC JACK.  
6
 
CAMERA INSTALLATION  
CONTROL BOARD  
2
3
1
1) Video Test Terminal  
For second video output  
2) OSD (On Screen Display) Joy stick  
Press the Joy stick for one second until the OSD menu tree  
appears on the screen. Move the Joy Stick up, down, left &  
right to control the OSD functions.  
3) Lens adjustment (for Zoom) Joy stick  
Adjust the Joy stick left or right to control between TELE &  
WIDE, Focus is automatically matched without any adjustment.  
7
 
CAMERA INSTALLATION  
COMPATIBILITY  
“A” type Box  
“B” type Box  
CVCTPEXT  
CVCTPLATE  
[CVCTPLATE Hole Description]  
Hole 1 : CVCTPEXT  
Hole 2 : Electrical Box “B” type  
Hole 3 : Electrical Box “A” type  
8
 
CAMERA INSTALLATION  
COMPATIBILITY  
BCP  
( USING  
)
7246WMT  
CVCTPEXT  
CVCTPLATE  
BCP (Direct connection )  
9
 
FEATURES  
FOCUS FREE  
With 3.7~10mm FOCUS FREE Auto Iris Motorized Zoom Lens,  
Focus can be automatically set up by adjusting zoom position.  
No more trips back to the installation to re-focus the camera.  
Reduces installation time and service calls.  
High Resolution  
Horizontal resolution of 550 TV lines is achieved by using a  
SONY Super-HAD CCD with 410,000 pixels, and a custom DSP  
yielding pictures with a high S/N ratio..  
DAY/NIGHT  
The camera can show color pictures in all lighting conditions.  
Or you can have it automatically switch to a B/W in low light  
conditions  
S-WDR (Speco WDR)  
This is Digital -WDR feature which enables to obtain clear and high  
quality pictures even in strong backlight condition.  
S-DNR (Speco DNR)  
This can remove image noise efficiently showing clean images in  
low light conditions.  
SLC (Speco BLC)  
When the image is in front of strong background lighting,  
your camera allows you to get a clear image.  
10  
 
FEATURES  
HLC (High Light Compensation)  
This function reverses bright spots in the picture (such as headlights).  
It enables the entire system to do a better job of resolving and  
displaying grayscale information such as a license plate.  
FREEZE  
This function freezes the current scene for detailed viewing.  
PRIVACY  
It also has the ability to mask up to 8 areas of the picture where  
Viewing is not desired. Each zone can be independently  
programmed via the OSD  
OSD  
All camera functions are menu driven for easy use.  
MIRROR  
Picture can be reversed vertically or horizontally.  
D-ZOOM  
Digital zooming up to 32X.  
11  
 
OSD MENU TREE  
LENS  
DC  
EXPOSURE  
SLC  
SHUTTER AGC SLC  
S-WDR RETURN  
HLC  
WHITE BALANCE  
ATW AWB AWC-SET MANUAL INDOOR OUTDOOR  
DAY / NIGHT  
COLOR AUTO EXT B/W  
S-DNR  
ON OFF  
SPECIAL  
CAM TITLE D-EFFECT MOTION PRIVACY RETURN / END  
FREEZE  
MIRROR  
D-ZOOM  
GAMMA  
NEG.IMAGE  
ADJUST  
SHARPNESS BLUE RED RETURN / END  
RESET  
FACTORY RETURN / END  
EXIT  
12  
 
OSD MENU DETAILS  
1. EXPOSURE  
[OPTION : SHUTTER / AGC / SLC / S-WDR / RETURN]  
- SHUTTER  
1/60, FLK, 1/250, 1/500, 1/2000, 1/5000, 1/10000, 1/100000  
- AGC (Low / Middle / High)  
Adjusts value of AGC gain and increases the GAIN level to brighten the  
picture. (noise / distortion may develop)  
- SLC  
* SLC : Back Light Compensation * HLC : High Light Compensation  
- S-WDR (Digital Wide Dynamic Range)  
To distinguish a subject in both bright and dark areas.  
* INDOOR : Activate S-WDR for Indoor use.  
* OUTDOOR : Activate S-WDR for Outdoor use.  
2. WHITE BALANCE  
[OPTIONS : ATW / AWB / AWC SET / MANUAL / INDOOR / OUTDOOR]  
- ATW  
Auto Tracking White Balance when the color temp in 1800°K~10500°K.  
- AWB  
Automatically adjust White Balance to your specific conditions.  
- AWC SET  
Set while pointing the camera towards a sheet of white paper.  
- MANUAL  
It allows you to increase or decrease the red or blue factor on screen.  
- INDOOR  
Select this when the color temp. is 4500°K~ 8500°K.  
- OUTDOOR  
Select this when the color temp. is 1800°K ~10500°K  
13  
 
OSD MENU DETAILS  
3. DAY / NIGHT  
[OPTION : COLOR / BW / AUTO]  
- COLOR : Full time color mode  
- BW : Full time black & white mode  
- AUTO: Automatically detect color or black/white  
* DELAY : Set Delay time to switch Color to B/W.  
* S-LEVEL : Set Start Level of luminance that you define.  
* E-LEVEL : Set End Level of luminance that you define .  
*** Only certified technicians should be allowed to this feature.  
4. S-DNR  
[OPTION : ON / OFF]  
- Reduces noise/distortion on the screen.  
Increasing the DNR level reduces noise but may introduce video artifacts.  
DNR is deactivated if AGC is turned off.  
5. SPECIAL - CAM TITLE  
[OPTION : ON / OFF]  
- Display a name and/or number on the monitor.  
14  
 
OSD MENU DETAILS  
6. SPECIAL – D-EFFECT  
[OPTION : FREEZE / MIRROR / D-ZOOM / GAMMA / NEG.IMAGE]  
- FREEZE: Freezes the current scene for detailed viewing.  
- MIRROR – ROTATE, V-FLIP, MIRROR  
- D-ZOOM : Digital zoom of 1 ~32X.  
- GAMMA : 0.45 is fixed. Do not adjust it unless certified technician.  
- NET. IMAGE : Change colors off like film.  
7.SPECIAL - MOTION  
[OPTION : ON / OFF]  
- To transmit a alert signal when it detects motion of an object on the  
screen. 4 Areas can be selectable.  
8. SPECIAL - PRIVACY  
[OPTION : ON / OFF]  
- Mask up to 8 areas of the screen  
9. ADJUST  
[OPTION : SHARPNESS / BLUE / RED ]  
- Adjust sharpness / RED and BLUE characteristics on the picture.  
10. RESET  
- Restore all factory default settings.  
15  
 
TROUBLESHOOTING  
If you have trouble operating your camera, refer to the following  
Problem  
Solution  
Nothing appears on  
the screen.  
Check that the power cord and line connection  
between the camera and monitor are correct  
Check that you have properly connected VIDEO  
cable to the camera VIDEO output jack.  
The image on the  
screen is dim.  
Is the lens stained with dirt? Clean your lens with  
soft, clean cloth.  
Set the monitor for the proper conditions.  
If the camera is exposed to too strong light  
change the camera position.  
Adjust the lens’ focus.  
The image on the  
screen is dark.  
Adjust the contrast feature of the monitor.  
If you have an intermediate device, set the  
75/Hi-z properly.  
The camera is not  
Check that you have properly connected  
working properly,  
and  
the camera to an appropriate power source.  
the surface of the  
camera is hot.  
MOTION DETECTION  
function is not active.  
Have you set ‘MOTION DET.’ menu to off?  
Have you set ‘MD LEVEL’ to too low?  
Have you set ‘MD AREA’ properly  
16  
 
TROUBLESHOOTING  
Problem  
Solution  
The color of the  
picture is not  
proper.  
Check that you have properly set the  
‘ WHITE BALANCE ’ menu  
The image on the  
screen flickers.  
Is the camera facing to direct sunlight or fluorescent  
lighting? Change the camera position.  
17  
 
LED PATTERN  
3.7-10mm FF lens  
18 Mini IR LEDs (80’ Range)  
18  
 
SPECIFICATIONS  
ITEM  
VLB11SCSFF  
12VDC Only  
Power Source  
Power Consumption  
Image Sensor  
Total Pixels  
600mA (DC)  
1/3”, SONY SUPER HAD CCD, 410,000 pixels  
811(H) x 508(V) , 1/3” CCD  
768(H) x 494(V) , 1/3” CCD  
Focus Free Lens 3.7~10mm  
1 : 1.3 ~2.0  
Effective Pixels  
LENS TYPE  
Maximum Aperture Ratio  
Scanning System  
2 : 1 Interlaced 525 Lines / 60 Fields / 30 Frames  
Synchronization  
Internal  
Video Output  
1.0V [p-p] Composite, 75  
550 TV Line  
Resolution  
Gain Control  
AGC-L, AGC-M, AGC-H, OFF selectable  
1/60 ~ 1/200,000 sec  
Electric Shutter Speed  
DAY / NIGHT  
COLOR / AUTO / BW  
COLOR TEMP (White Balance)  
Min. Illumination  
ATW / AWB / AWC-SET / MANUAL / INDOOR / OUTDOOR  
0.3 LUX (F 1.2), 0.00LUX (LED ON)  
52dB (Weight On)  
S/N ( Y signal)  
SPECO DNR  
ON / OFF  
Motion Detection  
On Screen Display ( O.S.D )  
PRIVACY Function  
Operational Temperature  
Operational Humidity  
ON / OFF (4 Programmable Zone)  
Built - in  
ON / OFF (8 Programmable Zone)  
-29~ +50( - 20~122)  
30% ~90% RH  
19  
 
DIMENSIONS  
* FRONT VIEW  
* SIDE VIEW  
20  
 
WARRANTY  
21  
 
MEMO  
 
MEMO  
 
200 New Highway  
Amityville, NY 11701  
631-957-8700  
VER. 090706  
This manual is based on the date as shown in the right and specifications are subject  
to Change without notice for quality improvement.  
 

Sennheiser Microphone e838 User Manual
Sherwood Stereo Receiver RD 5503 User Manual
Soleus Air Dehumidifier DP1 30 03 User Manual
Sony Camcorder PMW EX1 User Manual
Sony Car Stereo System D NF401 User Manual
Sony Digital Camera DSC H90 User Manual
Sony Radio ICF M55 User Manual
Speco Technologies Security Camera HTINTB10 User Manual
Sun Microsystems Network Card Sun Quad User Manual
Sunwave Tech Universal Remote SRC 3310 9320 User Manual